Thinking about the Solar Roofing question for a home in Plum Pennsylvania?

Find out how panels, tiles and roofing fit into a single plan

Contact us at 412-858-8858 before you commit to a layout

The Roof Under the Array Comes First: What Gets Checked First

Panels and roofing have to work together for decades; a clear look at the roof saves trouble at every later step. Roofs with several layers of old shingles are checked for weight and flat surfaces; a house that has been added onto may have a mix of framing types.

Moss, loose granules and curled shingles tell the roofer how much life is left; the outcome is a plain answer to the question of whether the roof is ready. Find out whether leaks have appeared in the past and where; patterns of old trouble point to a detail that needs correcting.

The easiest time to fix a roof is before anything is attached to it; each decision about the layout rests on what the roof can carry. Asphalt roofing wears out sooner than the equipment that sits on it; a roof with plenty of good years left carries an array without trouble.

Orientation, Pitch and Trees: The Slopes That Work

Solar Roofing depends on which parts of the roof see sunlight for long stretches of the day; the path of the sun is lower in winter, so shade lengthens in the cold months. Panels still produce power in diffuse light, though less than under a clear sky; a good plan is built on the actual roof, not on the brochure photo.

Every slope gets its own check, since a house can have good and poor sections side by side; a low winter sun reaches a south slope even when the days are short.

Simple gable roofs give long clear runs for panels; setbacks along the edges keep panels clear of the places where wind lifts hardest. Shade from the landscape belongs in the plan; a shaded roof still makes sense when only part of the surface is used.

A site plan is tested hardest in the cold months; evergreen trees shade a roof all year, while bare trees let light through in winter.

Panels on Top or Tiles in the Roofline: How the Styles Differ

Panel racks are the most common way to carry solar on a pitched roof; a rack system leaves the existing roofing in place and adds a layer above it. Solar Roofing with tile-style modules asks for patient, exact work; a failed connection under the tiles is harder to reach than one on a rack.

Neighbors and homeowner associations may care about how the system looks from the street; flush products take more careful flashing at every edge.

Each style needs its own installation method and its own flashing details; the roofing material underneath decides which products can be used. Water management comes first, because the electrical side depends on a dry roof; edges, ridges and valleys still follow the rules of good roofing.

Where Hardware Meets Roofing: Seals, Boots and Brackets

In Solar Roofing, the attachment points are among the most important details on the whole roof; a bead of sealant alone is not a lasting answer. Wood shakes and older asphalt shingles may need extra care around each mount; the damage from a mismatch shows up over the seasons rather than on day one.

Sealant is applied under the flashing and over the fasteners, not as a patch afterward; a wet roof and a drill do not belong together, so the schedule follows the weather.

A solar mount is a tiny roof repair waiting to be done well or badly; a mount sealed with care outlasts one sealed in a hurry.

Wind is a real force on a roof, and arrays have to be held down for it; a roof that is sound under the array resists wind far better than a tired one. Rain and meltwater find the gaps between panels and run down the shingles below; the surface under the array is checked at the same time as the rest of the roof.

Snow, Ice and the Cold Season: Planning for Winter

Panels have smooth surfaces and snow can slide off them all at once; the plan for a long, steep roof differs from the plan for a low shed. An ice-and-water barrier is worth having along the eaves and in the valleys; keeping the roof deck cold and even is still the first defense.

Cold snaps leave frost on panel glass that lets go in a sheet at the first thaw; clear paths to doors and steps matter more under a slick roof.

Winter ice and a solar array have to coexist on the same roof; solar equipment does not cure ice dams, and it does not cause them.

The Roof Side and the Wiring Side: A Handoff Between Trades

Solar work splits between two trades, the roofer and the electrician; conduit runs through the attic or along an outside wall, and the route should be settled early. Good coordination saves repeated trips and delays; panels cannot go on until the mounts are flashed and the roofing is complete.

Roof-to-attic wiring passes through a sealed opening that matches the flashing around a vent pipe; keeping the attic clean and dry helps both crews work safely.

The roofer needs to know where that route crosses the roof and the attic; a plan drawn on paper beats a decision made on the roof.

Roof First, Solar Second: Detach and Reset

The simplest plan is to finish roof repairs before panels go on; the two projects share staging, scaffolding and access. Detaching and resetting panels takes planning, since the wiring and mounts must be handled safely; the electrical side must be shut down before anyone touches the panels.

Putting off a needed roof repair until after the array is up makes the work harder; a crew can finish the roofing, then hand the roof over for the array.

Looking after a roof gets a little more involved once panels are on it; the owner and the roofer share the job of keeping the system watertight.

A roof done in spring or fall leaves the summer sun for the array; the weather windows in the region are limited, so planning matters.

Care for a Roof Under Panels: Small Habits, Long Life

Walk the yard after a big storm and look over the roofline and the edges of the array; a loose bracket or a shifted rail is easier to fix when caught early. Anything that needs hands on the roof is left to people with the proper harnesses and gear; moss grows faster on a shaded roof and spreads under the lower edge of panels.

Let Us Help You Plan the Roof Side: Describe the House

The Roofing Company can walk the roof with you and talk through what a solar plan would involve; reach out at 412-858-8858 and describe the roof. A short talk about the roof now can shape a better plan later; a roof that is ready for solar makes the rest of the project simpler.

 

Charles Kotulsky

Verified

★★★★★
We used John and The Roofing Company to replace our roof before the summer. They showed us the Atlas shingles and we went with the hearthstone color. They removed the old roof and put the new one on all in one day which was great. We love how it looks and will be calling them for siding next year

michael Zawodni

Verified

★★★★★
Put a roof over our deck, very professional, kept jobsite clean everyday, and went above and beyond with quality and craftsmanship. Couldn't recommend this company more!! Best around.

Chris Juricich

Verified

★★★★★
The price was right, and most importantly our new roof looks beautiful. It was also delivered on-time and with great communication throughout.

Mark Lehner

Verified

★★★★★
The Roofing Company LLC is hands down the most knowledgeable and professional contractor I’ve worked with. Their team is incredibly attentive, responsive, and reliable—from the first call to the final inspection. What truly sets them apart is their deep understanding of not just roofing, but the entire construction industry. John is a true professional with years of hands-on experience and insight. His knowledge goes far beyond shingles and gutters—he understands this industry from the ground up, and it shows in every detail of the job. If you’re looking for a contractor who delivers quality, communicates clearly, and stands behind their work, look no further. The Roofing Company LLC is the real deal.

Michael Long

Verified

★★★★★
Attention to detail was great , very professional company