Solar Roofing

Thinking about your Solar Tile Installation near Plum Pennsylvania?

Learn what the roof has to offer before anything is mounted

Dial 412-858-8858 to ask how the roof side of solar works

Solar Is Only as Good as the Roof Beneath It: What Gets Checked First

Panels and roofing have to work together for decades; a roof that is nearly worn out is better replaced before the panels go on. A roofer looks for sagging, rot and weak spots in the sheathing before any hardware goes down; the crew documents what it finds with photographs.

The attic side of the deck shows stains, damp insulation and daylight where none should be; any single finding changes the schedule before the array is designed. Ask how old the roofing is and how many layers it carries; the owner's knowledge of the house fills gaps no inspection can reach.

The easiest time to fix a roof is before anything is attached to it; the same crew that reads the roof can explain the choices. Solar equipment is built to last for a very long time; the age of the roof is the first fact on the planning sheet.

Orientation, Pitch and Trees: The Slopes That Work

The direction and tilt of each slope decide how well a solar array can perform; the path of the sun is lower in winter, so shade lengthens in the cold months. Panels still produce power in diffuse light, though less than under a clear sky; trees that were small at planting have grown past the roofline.

Tilt matters too, because steep and shallow roofs catch light at different angles; a low winter sun reaches a south slope even when the days are short.

Simple gable roofs give long clear runs for panels; valleys and ridges set limits on where rails run. Shade from the landscape belongs in the plan; trimming a limb is an easier fix than moving an array.

A site plan is tested hardest in the cold months; leaf-out in spring changes the picture for the roof within weeks.

Two Ways to Put Solar on a Roof: Appearance and Detailing

Rails and clamps hold the panels a few inches above the surface so air can pass beneath; the look, the layout and the wiring plan all depend on the system chosen. Solar Tile Installation with tile-style modules asks for patient, exact work; the roofing details at edges, valleys and penetrations still follow roofing rules.

Panels sit proud of the roofing, while integrated tiles sit flush with it; the look of the roof is part of the value of the house.

Others are large flat modules that sit on the roof like glass panels; a roof that matches the architecture of the house looks right from the street. Careful handling matters because the pieces are heavier and more delicate than shingles; the crew staggers the pieces and checks the connections as the rows go up.

Attachments, Flashing and Sealing: Seals, Boots and Brackets

Each mount is a place where the roof surface is pierced, and each one needs proper flashing; the mount is set into sealed layers so water flows around it and not under it. Slate and clay call for special brackets that grip without cracking the material; careful planning keeps the roof watertight under the array.

Mount spacing follows the layout so the load is spread through the framing; a wet roof and a drill do not belong together, so the schedule follows the weather.

The crew chooses hardware that suits the roof, whether shingle, slate, tile or metal; a mount sealed with care outlasts one sealed in a hurry.

Wind is a real force on a roof, and arrays have to be held down for it; the roofer reviews the edge details with the same care as the field. Rain and meltwater find the gaps between panels and run down the shingles below; leaves and grit wash down under the panels and collect at the lower edge.

Cold-Season Realities: Protecting What Is Below

Snow behaves differently on glass-faced panels than on shingles; the plan for a long, steep roof differs from the plan for a low shed. Insulation and attic ventilation still decide how snow melts across the roof; solar does not change the need for a dry, well-ventilated attic.

Snow load is part of the structure's design, so the framing has to carry it; winter proves whether a solar plan was thought through.

Ice dams and solar arrays share a roof; a roofer reading the attic helps the whole system work as intended.

Wires, Inverters and the Attic: A Handoff Between Trades

The path from the roof to the panel in the house has to be planned with both trades in mind; the electrical connection to the utility is a separate step from the roof work. A Solar Tile Installation project goes smoothly when one person keeps the schedule in view; every trade has its own tools, its own schedule and its own habits.

Conduit and junction boxes on the roof are kept off the surface where water runs; keeping the attic clean and dry helps both crews work safely.

The roofer needs to know where that route crosses the roof and the attic; a quick call between the trades saves a day of waiting.

Roof First, Solar Second: Detach and Reset

A roof replaced before the array is installed gives a fresh surface under every panel; there is no need to pay twice to open the same part of the house. Detaching and resetting panels takes planning, since the wiring and mounts must be handled safely; the removal and reinstallation of panels is slower than the roof repair itself.

A new roof gives an array a long, quiet future; a crew can finish the roofing, then hand the roof over for the array.

Every few seasons the roof, the mounts and the flashing are checked for wear; a short checklist after the first winter confirms that everything held.

Scheduling the roof and the array together pays off; the sequence is written down so nobody has to guess.

Checkups After the Array Goes On: A Simple Routine

Keep a photo of the roof from each side so changes are easy to spot over time; a flashlight in the attic shows damp spots that cannot be seen from outside. Climbing onto a roof with panels is never a casual job because the glass is slippery; a short visit after the first winter confirms that mounts and flashing held up.

The First Step Is a Roof Walk: Describe the House

Our team at The Roofing Company answers questions about roofing, mounts, flashing and winter; reach out at 412-858-8858 and describe the roof. Tell us what you see from the ground, and we will help you sort out the next move; weather will not wait, and neither should the questions.

Charles Kotulsky

Verified

★★★★★
We used John and The Roofing Company to replace our roof before the summer. They showed us the Atlas shingles and we went with the hearthstone color. They removed the old roof and put the new one on all in one day which was great. We love how it looks and will be calling them for siding next year

michael Zawodni

Verified

★★★★★
Put a roof over our deck, very professional, kept jobsite clean everyday, and went above and beyond with quality and craftsmanship. Couldn't recommend this company more!! Best around.

Chris Juricich

Verified

★★★★★
The price was right, and most importantly our new roof looks beautiful. It was also delivered on-time and with great communication throughout.

Mark Lehner

Verified

★★★★★
The Roofing Company LLC is hands down the most knowledgeable and professional contractor I’ve worked with. Their team is incredibly attentive, responsive, and reliable—from the first call to the final inspection. What truly sets them apart is their deep understanding of not just roofing, but the entire construction industry. John is a true professional with years of hands-on experience and insight. His knowledge goes far beyond shingles and gutters—he understands this industry from the ground up, and it shows in every detail of the job. If you’re looking for a contractor who delivers quality, communicates clearly, and stands behind their work, look no further. The Roofing Company LLC is the real deal.

Michael Long

Verified

★★★★★
Attention to detail was great , very professional company