
Weighing Flat Roofing Installation for a flat section of your building near McKeesport Pennsylvania?
The crew at The Roofing Company can show why a flat roof is judged by its drainage first
Reach us at 412-858-8858 and describe the roof as it stands
A Flat Roof Is a Drainage Problem: a Plain Explanation
Rain does not run off a nearly level surface the way it runs off a steep one, and standing water finds weak points; every low spot on the surface gets noticed by water sooner than by people.
Many Pittsburgh houses and rowhouses have a flat section over a porch, a rear addition or a kitchen, and the rules of drainage apply there as much as anywhere; a small flat patch can leak just as badly as a large one.
Before you decide on Flat Roofing Installation, find out how the roof drains now and what blocks it; photographs taken a day after rain show the problem clearly.
What a Pittsburgh Winter Does to a Membrane, Season by Season
Snow sits longer on a flat roof than on a steep one, and the weight adds up when a heavy storm follows another; ice at a scupper can back water up behind the parapet.
Membranes expand and shrink as the temperature swings, and the movement pulls on seams, corners and flashings; spring is the right time to look for damage the winter left behind.
Winter wear shapes every decision about Flat Roofing Installation, from the material to the way the seams are made; compare what each proposal says about winter.
Membrane Choices Compared: Strengths and Limits
Rolled asphalt membranes arrive in long sheets that are attached to the roof and to each other in overlapping layers; patches are cut from roll material and sealed at the edges.
Synthetic rubber sheets are made wide enough to cover most of a small roof in one piece, which cuts down the number of joints; seam tape needs a clean, dry surface to hold.
A white single-ply membrane with welded seams reflects sunlight and forms a tight bond where sheets overlap; details around curbs and corners are cut and welded by hand.
Some roofs that seem flat are actually low-slope and can take a different kind of covering, such as an interlocking or tiled product; manufacturers publish the minimum slopes they allow.
A thorough proposal for Flat Roofing Installation describes the layers from deck to surface; ask what the crew would pick for a roof like yours.
The Layers Beneath the Membrane, and What Can Go Wrong
Under the visible surface there is usually a deck of wood or metal, a layer of insulation and sometimes a vapor barrier; a moisture scan or core sample can show what is hidden.
Tapered insulation boards are cut at a slight angle, which builds a fall into a roof that was made too flat; new boards can fix a chronic pond.
A proposal for Flat Roofing Installation ought to say whether the old roof is torn off or covered and why; ask how the crew checks for wet insulation.
Edges, Walls and Roof Penetrations, One Detail at a Time
Flashings turn the membrane up a wall and seal it, and they are among the most common places for water to enter; corners are cut and folded by hand and need care.
Anything that sticks up through a flat roof, such as a vent stack, a skylight, a chimney or a unit of equipment, needs flashing of its own; a skylight curb is worth a look before the membrane goes over it.
Before you decide on Flat Roofing Installation, ask how the walls, curbs and drains will be tied into the new surface; ask who will check the finished flashings.
Repair, Recover or Replace, Before You Commit
Not every leak means a new roof, since a single split seam or a worn flashing can be repaired in a short visit; repairs are easier on a roof that has been cleaned.
A recover puts a new membrane over the old one, while a tear-off removes the old roof down to the deck first; the condition of the insulation often settles the question.
Anyone weighing Flat Roofing Installation should be shown the condition of the roof, with photographs where possible; compare the scope, not just the material.
What the Crew Does, Step by Step, Piece by Piece
Before new work begins, loose gravel, debris and failed flashings are taken away and the deck is checked; weather decides when each step can happen.
Flashings at walls, curbs and pipes come after the field of the roof is laid, and then edges and drains are finished; photographs of each detail make a handy record.
- Which membrane do you suggest for this building and why, and how will it be written down?
- What happens at each pipe and vent, and what are the trade-offs?
Working Safely Above Your Head: Simple Precautions
Frost, dew and a thin skin of ice turn a smooth membrane into a skating surface on cold mornings; ladders are tied off and the landing spot is kept clear.
Membranes and adhesives need dry surfaces and suitable temperatures, so a job on a low roof is planned around the weather and not only the calendar; materials stored on the roof need protection from wind and wet.
Questions about Flat Roofing Installation can include which season suits the work and what happens if the schedule slips; photographs of the access points help a crew plan.
Simple Upkeep, Season by Season, Twice a Year
Clear the drains, scuppers and gutters in the fall, after the leaves come down and before the first hard freeze; keep foot traffic on the roof to a minimum.
A roof that is inspected twice a year and cleaned often can last much longer than one that is ignored; early action keeps small leaks small.
Upkeep is part of any plan for Flat Roofing Installation, since even a fine membrane still needs clear drains and a watchful owner; bring up your own plans for rooftop equipment.
Take the Next Step, Whenever You Are Ready
A low roof keeps everything beneath it dry, so the choice of how to cover it is worth careful thought; bring your questions and any photographs of the roof.
Call 412-858-8858 to talk about Flat Roofing Installation in McKeesport Pennsylvania; we will keep the talk plain and practical.













